Wood Bathroom Vanity | Custom by DBM Factory

Wood Bathroom Vanity

A wood vanity puts grain at the bathroom centerpiece. Stone counters, tile walls, glass shower — everything else in the room reads hard and reflective. A wood front softens that. Oak ages golden under daily light. Walnut deepens. Teak holds up around moisture better than most. The vanity becomes the warm note in a room of cool surfaces.

We design and produce each wood vanity around your project. Share the bathroom dimensions, plumbing rough-in positions, and a designer reference. We turn it into a working drawing and build the cabinet ready for shipment.

Choose the Right Wood for the Bathroom

Where It Fits — Four Common Project Types

From Sketch to Site — Three Stages

After delivery, your contractor or installer handles fitting. We provide an assembly guide and a step-by-step video. Where local installation is available in your region, we can help you find a vetted installer.

Wood Bathroom Vanity

Keeping Real Timber Alive in a Steamy Ensuite — Where Damp Air Rules.

Real timber lives hardest in a compact, busy ensuite, because the room saturates with steam after every hot shower. The warm grain still wins on appearance, yet the humidity tests the construction behind that warmth more than any other interior.

Owners reach us at a familiar moment, when they love a timber front but worry it will swell or split. The concern is reasonable, so the conversation is rarely about the wood species alone. It is about detailing the cabinet to tolerate a wet room without warping or peeling at the edges over time.

Why the Build Matters More Than the Grain.

Timber expands as the room breathes, so it swells in steam and contracts again as the air dries. The solution is not a harder wood; it is a construction that lets the panel move a little without the joinery opening. That single principle shapes every decision we make for a wet environment.

Sealing carries equal weight, and the vulnerable point is always the cut edge near the basin. A surface coat alone leaves the raw edge exposed, so moisture penetrates where the eye never travels. We seal every face, edge, and underside, because the concealed surfaces determine how long the front survives.

Air circulation is the quiet third factor that owners rarely picture. A vanity pressed flat against a wet wall traps condensation behind the carcass with nowhere to escape. A modest ventilation gap and a recessed toe space encourage circulation, so the back stays drier through daily use.

How the Detail Shifts With the Wet Zone.

A Tight Wet Ensuite vs an Airy Family Bath.

Room dimensions set the moisture load the timber has to handle. A compact ensuite with a glass shower close by retains steam far longer, so it requires the most water-tolerant species and the fullest seal specification. A larger family bathroom dries faster between uses, which gives a gentler, more forgiving condition. The look stays timber, while the construction quietly hardens to match the surrounding air.

Beside the Shower vs Across the Room.

Where the vanity sits changes the exposure it absorbs every day. A cabinet positioned next to the shower screen meets direct spray, so we recommend teak-type timber and a tougher edge seal there. A vanity located across the room receives only ambient humidity, which opens up a wider species selection. We map that position on the working drawing before confirming the timber and the finish coat.

A Solid Timber Front vs a Veneered Core.

The core behind the face matters as much as the visible timber. A full solid-timber front reads warmest, yet it moves the most and suits a calmer, drier location. A timber veneer over a stable moisture-resistant core holds flatter in heavy steam, while still showing genuine grain. We discuss this trade-off in full before a single panel is cut.

What Coordination Looks Like for a Timber Wet Room.

Drawing-First Coordination starts with the hard facts of your wet room. We pin the shower position, the basin centre, and the plumbing rough-in before anyone touches the timber. The working drawing then locks the species, the seal spec, and the ventilation gap, so the damp detail is settled early rather than guessed on site.

Trial Assembly Before Packing then builds the whole vanity upright on our Guangdong workshop floor. We check the door fit, the edge seal, and the drawer travel, then photograph the result before taking it apart. We label each part as it comes off, so the build in your bathroom stays a clean bolt-together job.

Export-Ready Crating packs the timber parts in the order your installer will set them. We wrap the sealed faces against knocks and damp for the long ocean leg ahead. The crate lands ready to open, with the heavy carcass seated low for a safe, steady lift.

What to Send Us About Your Bathroom.

A rough plan or a quick phone photo of the room gives us a strong start. Mark where the shower sits and how close it falls to the vanity wall. Add the plumbing rough-in position, which is simply where the waste and water enter behind the cabinet.

One more line helps us read the moisture your room will throw at the timber. Tell us whether the space is a tight ensuite or an open family bathroom, and how it vents. From there we turn your notes into a working drawing and a vanity built for the steam.

After delivery, fitting is on your side. On site, your contractor or installer handled fitting directly from our drawings, with our assembly guide and step-by-step video to follow — or use your own local installer where needed.

See the Floating Bathroom Vanity → · compare the Shaker Bathroom Vanity → · browse the full Vanity Cabinet range → · or pair it with a Frameless Shower Room →